s India line indentation Die important material, the indentation on the cardboard box, forming a significant impact. How to distinguish product quality is good or bad, we teach you four strokes:
Identify cartons instruments have an indentation line: indentation groove width and height of error identification
Poor indentation line for small factories produce more, these small factories generally not professional product development and laboratory quality control, thus products uneven, less accuracy, great error. If the indentation model 0.5X1.5mm line, in accordance with strict laboratory testing, poor indentation line indentation slot width of a 1.6mm - 1.8mm actually measured values is not one of its standard 7.5mm range. And quality of the models indentation lines, indentation groove width of the range of 1,48 mm ~ Yudong, the error can be controlled in less than 2%. Again indentation trough height, poor indentation trunkings high measured values for 0.52mm ~ O. 55mm, the biggest error to 10%. The same type and quality products, indentation trough height measured in 0.50-0. MSRPs between error control less than 2%. Thus, poor indentation line indentation trough error is very, very easy to produce a series of quality problems.
Identify cartons indentation lines are two instruments: the difference identify material
In addition to the accuracy of inferior products, errors, in various important positions cut corners, resulting in a decline in the quality of products. To grab market share, poor indentation line production plant used to jerry-ways to reduce product costs, which their products can be a relatively low price to enter the market. If the indentation at the end of the width module to model the indentation of 0,5 x7.5mm example, poor quality products at the end of the module width generally only 1.82mm, and high-quality products can reach two. 5mm. The broader width means more die at the end of the contact area is conducive to die at the end of the spear sticking more firmly on the floor Die.
Again protection mode at the end of the tape, poor quality products used in the belt width or even narrower than to die at the end, the consequences of the end of the module is in use before losing the protection of plastic protection, it is easy to lose when viscous. When running high-speed die-cutting machine, swap out easily die at the end, lead to die-cutting machine damaged. A shutdown, machinery maintenance, the loss would be greater. And quality indentation at the end of the line model can be fully protected tape wrapped die at the end, the whole model in use at the end when a strong cohesive, effective avoid indentation line for the machines off and cause damage, but also improve the precision die-cutting.
Identify cartons indentation lines are three instruments: identifying raw materials
Quality indentation of a better quality of raw material production, more uniform product line. The poor indentation line is used inferior materials, difficult to improve product performance. If at the end of the protection belt model, in order to guarantee the protection of the tape can meet stringent quality requirements, the quality of the production plant no indentation from the tape plant procurement, because generally the tape does not apply to the production line indentation, and the margin of error of its tape can meet the requirement. Therefore, the powerful indentation of the plant will set up a special tape production line, dedicated production line for the indentation belt. Indentation and general line production plants, obviously do not have an investment professional can tape production line strength, often bought from the market ordinary plastic receptacle for indentation of the production, use of such material production lines derived indentation quality can be imagined.
Identify cartons indentation lines are four instruments: product development identified
Factory production line quality indentation pay more attention to product development, and production of low-quality plant indentation only focus on local interests. Lack of research and development so that these poor indentation line production plant lost forward thrust, but merely waiting for the other manufacturers developed for the product, a little disguise to be copied, but often unknown why they are so informed, however, get their products but nondescript. If the indentation of the positioning seals, each the size of the indentation should use different size positioning seals with indentation of positioning can guarantee the complete right now. The indentation of the general plant may not be a pupil studying in all the indentation of the same specifications are used positioning seals, which use their frequent positioning line indentation not easily shift such phenomena.
Poor indentation of the dimple easily lower the quality, and is likely to have a pair of die-cutting machine tremendous harm. Carton plant to purchase these poor indentation line, seemingly cheap, can reduce production costs, but these products low precision, specifications error, there is no guarantee quality, but easily led to production efficiency, product uneven one. If not timely delivery, customer returns, greater losses.
As the old saying says: tools, the first of its profits. Choose good quality suppliers and procurement for the indentation of your production can be a perfect tool products.